Repointing9 min read

The Best Mortar Mix for Repointing Old Brickwork

Using the wrong mortar on old brickwork can cause serious damage. Here's how to choose the right mortar mix for repointing — whether your house is Victorian, Edwardian, or post-war.

DR

Daniel Rosser

Published 5 September 2026

Choosing the right mortar mix for repointing is one of the most important decisions you'll make — and getting it wrong can cause more damage than leaving the old mortar in place. The golden rule is simple but often ignored: the new mortar should be softer and more breathable than the bricks.

Here's how to choose the right mortar for your property, whether it's a Victorian terrace, an Edwardian semi, or a 1950s build.

The Big Mistake: Cement Mortar on Old Brickwork

The most common mistake — and it's a serious one — is using hard, cement-based mortar to repoint old brickwork. Here's why it's a problem:

Old bricks (pre-1930s) are relatively soft and porous. They're designed to "breathe" — moisture enters the brick and evaporates out through the mortar joints. When you use hard cement mortar, the moisture can't escape through the joints, so it evaporates through the brick instead. This causes the brick face to spall, flake, and eventually crumble.

In other words, hard cement mortar on soft old bricks forces the moisture to destroy the bricks instead of passing harmlessly through the joints. It's an expensive mistake that can ruin an entire wall.

Lime Mortar vs Cement Mortar

Feature Lime Mortar Cement Mortar
Flexibility Flexible — moves with the building Rigid — cracks under movement
Breathability High — allows moisture to evaporate Low — traps moisture
Best for Pre-1930s properties, solid-wall construction Post-1930s properties, cavity walls
Durability 50+ years when done correctly 15-25 years
Cost Higher (specialist material + skill) Lower (standard material)

Which Mortar Mix for Your Property?

Pre-1900 (Victorian and Earlier)

Use a hydraulic lime mortar, typically NHL 3.5 or NHL 2.0, mixed with sharp sand. A common mix is:

  • 1 part hydraulic lime (NHL 3.5)
  • 2.5-3 parts sharp sand
  • Mixed with water to a workable consistency

For very soft historic brickwork, a putty lime mortar may be more appropriate. If in doubt, consult a specialist — this is not the place to guess.

1900–1930 (Edwardian and Early 20th Century)

Most properties from this era still need lime-based mortar, but you may be able to use a slightly stronger mix:

  • 1 part hydraulic lime (NHL 3.5)
  • 2-2.5 parts sharp sand

Some late 1920s properties with harder bricks may tolerate a weak cement-lime mix, but lime is still the safer choice.

1930–1950 (Interwar and Early Post-War)

Properties from this era typically have cavity walls and harder bricks. A cement-lime mortar is usually appropriate:

  • 1 part cement
  • 1 part lime
  • 5-6 parts soft sand

The lime in the mix improves workability and breathability without being too soft. This is a versatile mix that works for most post-1930s properties.

1950s Onwards

Modern properties with hard engineering bricks and cavity walls can take a standard cement mortar:

  • 1 part cement
  • 5-6 parts soft building sand

Or with a plasticiser additive instead of lime. This is the standard modern mix and is perfectly appropriate for newer properties.

How to Tell Which Mortar Your House Has

If you're not sure whether your existing mortar is lime or cement, here's a simple test:

  1. Visual inspection: Lime mortar is usually lighter in colour, often cream or off-white. Cement mortar is typically grey.
  2. Hardness test: Press a screwdriver or key into the mortar. Lime mortar will mark easily and feel chalky. Cement mortar will be hard and difficult to mark.
  3. The acid test: Put a small piece of mortar in white vinegar. Lime mortar will fizz and dissolve. Cement mortar won't react much.
  4. Look at the joints: If the mortar has eroded evenly and the bricks are in good condition, it's likely lime. If the mortar is hard but the bricks are spalling, it's likely cement has been used on a property that needs lime.

Sand Choice Matters Too

The sand you use in your mortar mix is just as important as the binder (lime or cement). For repointing:

  • Sharp sand (coarse, angular grains) is best for lime mortar — it provides good breathability and a traditional appearance
  • Soft building sand (fine, rounded grains) is used for cement mortar — it's easier to work but less breathable
  • Match the sand colour to the existing mortar as closely as possible — your local builders' merchant can help

Common Repointing Mistakes to Avoid

  • Using cement mortar on old brickwork — the #1 mistake, causing brick spalling
  • Raking out too shallow — you need to remove at least 15-20mm of old mortar for the new mortar to bond properly
  • Wet mortar smeared on brick faces — clean as you go, don't leave it to dry
  • Pointing in frost or very hot weather — mortar won't cure properly in extreme conditions
  • Using a mortar gun — they look quick but produce a poor, shallow result that won't last

When to Call a Specialist

If your property is pre-1930, has solid walls, or is a listed building, repointing with the correct lime mortar is a specialist job. Getting it wrong can damage the bricks and the building's breathability — potentially leading to damp problems that are far more expensive to fix than the repointing itself.

If you're in Hampshire, Berkshire or Surrey and want professional repointing with the correct mortar for your property type, we can help.

Advertisement

Need a Professional?

Get a Free Quote from a Brickwork Specialist

If you're in Hampshire, Berkshire or Surrey, Rosser Brickwork & Repointing Services Ltd can handle your repointing, chimney repairs or brick restoration. Fully insured, free quotes, no pressure.