Brick Restoration9 min read

Spalled Bricks: Why They Crumble, What Repair Costs, and When to Replace (UK 2026)

Bricks flaking or crumbling on the face? Here's what causes spalling, the repair options, what each costs in the UK, and when replacement is the only real fix.

DR

Daniel Rosser

Published 21 October 2026

Spalled bricks are bricks where the face has flaked, peeled or blown off, leaving a rough, crumbling or pitted surface. It is one of the most common brickwork faults we see on UK houses, and it nearly always has a cause that can be fixed. The sooner you deal with it, the cheaper the repair.

This guide explains why bricks spall, how serious it is, what the repair options are, and what you should expect to pay in 2026.

What Is Brick Spalling?

Spalling is when the outer face of a brick breaks away. You might see thin flakes, shallow dish-shaped craters, or the whole face of the brick coming off in a sheet. Underneath, the brick is often softer, darker and more porous than the original surface, which means it absorbs even more water and gets worse each winter.

Most fired clay bricks have a hard outer skin. Once that skin is broken, the soft interior is exposed and starts to decay quickly.

Why Do Bricks Spall?

Spalling is a symptom, not the underlying problem. Water is almost always involved. Here are the usual causes.

Frost damage

Bricks absorb water. When that water freezes it expands, and the pressure pushes the face of the brick off. This is worst on exposed walls, chimney stacks, garden walls and anywhere that stays wet, such as below a leaking gutter or at the base of a wall.

Cement mortar on soft bricks

This is the cause we see most on older houses. Older bricks are relatively soft and were laid in soft lime mortar. If someone repoints with hard cement mortar, the wall can no longer move or breathe the way it was designed to. Moisture can only escape through the bricks instead of the joints, so the brick faces take the damage and spall. The mortar stays perfect while the bricks fall apart. Our guide to the best mortar mix for repointing old brickwork explains the difference in more detail.

Salt crystallisation

Salts in the wall, from the bricks themselves, from groundwater or from old chimney flues, dissolve in water and move to the surface. When the water dries out, the salts crystallise just beneath the face of the brick and push it off. White powdery deposits on the wall are a clue that salts are present.

Poor quality or underfired bricks

Some bricks were never very durable, particularly certain Victorian and Edwardian batches and cheaper bricks from some periods. Underfired bricks have a weak, porous structure and spall even when everything else is right.

Painted or sealed brickwork

Masonry paint and waterproof sealants can trap moisture inside the wall. The water cannot escape, so it freezes and pushes the face of the brick, and the paint, off together. If your painted brickwork is flaking, spalling is often the reason.

Water that keeps getting in

Failed gutters, leaking downpipes, high ground levels, blocked weep holes and missing flashings all keep brickwork wet. Even good bricks will spall if they are saturated every winter.

Past cleaning damage

Sandblasting or harsh acid cleaning can strip the hard outer skin from a brick. The wall looks clean for a year or two, then starts to spall. Cleaning should always be done gently. See our guidance on brick cleaning methods if you are considering it.

How Serious Is Spalling?

It depends on how far it has gone.

  • A few isolated bricks: usually cosmetic and cheap to fix, but find out why they failed.
  • Patches or a whole elevation: a sign of an ongoing moisture or mortar problem that will keep spreading.
  • Deep spalling on a chimney stack: treat as urgent. Chimneys are exposed on all sides, and loose bricks at height are a safety risk.
  • Spalling that has gone through to the inner leaf or cracks the wall: get it assessed before anything else.

Spalling rarely makes a wall unsafe in the short term, but it does let water in, shortens the life of the wall and puts off buyers if you plan to sell. A surveyor will often flag it.

Repair Options for Spalled Bricks

The right repair depends on how deep the damage goes and what caused it. Whatever you choose, the cause must be fixed first or the problem comes back.

1. Do nothing (monitor it)

If the spalling is minor, the brick is otherwise sound and the cause has been dealt with, the damaged brick face often stabilises once it is dry and the water is under control. Photograph it and check it each spring.

2. Repoint with the correct mortar

If hard cement mortar is the cause, the joints need to be raked out and repointed in a softer, more breathable mortar, usually lime-based. This stops further damage and takes the load off the bricks. Read more in our lime mortar repointing guide. Expect to pay around £60 to £80 per square metre for professional repointing.

3. Turn the brick

If a brick has spalled on one face, it can sometimes be carefully cut out and turned round so the sound back face shows. This only works where the brick is deep enough and the back face is in good condition. It is a skilled job and not suitable for every wall.

4. Replace the bricks

Where spalling is deep, the only lasting repair is to cut out the damaged bricks and build in replacements. The hard part is the match. New bricks rarely look the same as 100-year-old ones, so we source reclaimed bricks or carefully matched new ones. Cutting out and replacing individual bricks is skilled work, and getting it wrong leaves obvious patches.

5. Brick repair mortar or "plastic repair"

For shallow spalling, a tinted repair mortar can be applied to the damaged face and shaped to match. It is a cosmetic repair that suits small areas and low-visibility walls. It does not last as long as replacing the brick, and a poor colour match shows.

6. Consolidants and sealers

Some products claim to strengthen decayed brick. These are specialist treatments, mostly used on historic buildings, and they are not a general fix. Avoid waterproof sealants on ordinary brickwork. They can trap moisture and make spalling worse.

How Much Does Spalled Brick Repair Cost in the UK?

Prices vary with the number of bricks, access and how matched the replacements need to be. These are realistic 2026 ranges based on what we quote for real jobs.

RepairTypical cost
Repointing a wall (cause: cement mortar)£60 to £80 per m²
Replacing individual spalled bricksPriced per job, usually a minimum call-out plus a rate per brick
Rebuilding a section of wall or chimney stackPriced after inspection
Scaffolding for work above ground floor height£500 to £1,000+ on top, depending on the property

Scaffolding is a separate cost on any job above ground floor height, and it can be a large part of the bill. If you have several jobs that need scaffold, such as spalling repairs, chimney work and repointing, doing them together saves a lot.

To get a rough idea of the repointing element, use our repointing cost calculator. It uses real rates and shows scaffolding as its own line, so there are no surprises.

What affects the price?

  • Number of bricks affected: a handful is a small job. Hundreds is a rebuild.
  • Brick match: reclaimed or special-order bricks cost more than standard ones.
  • Height and access: anything needing scaffold or a tower costs more.
  • Cause of the problem: if you also need repointing, gutter repairs or damp work, the total goes up.
  • Chimney stacks: heights and exposure make these dearer than ground-level walls.

Can You Fix Spalled Bricks Yourself?

Small, low-level areas can be done by a careful DIYer, but be realistic.

Reasonable DIY:

  • Fixing leaking gutters and downpipes
  • Clearing blocked weep holes and lowering soil levels against the wall
  • Removing a sealant or paint that is trapping moisture (take advice first)

Leave to a professional:

  • Cutting out and replacing bricks, which risks damaging neighbouring bricks and the wall above
  • Repointing in lime, which needs the right mix and technique
  • Anything on a chimney or above ground floor height
  • Any wall that is bulging, cracked or leaning

Cutting out the wrong way is easy to do and difficult to undo. If you are unsure, an inspection costs far less than a failed repair.

How to Stop Bricks Spalling in the First Place

  1. Keep water away from the wall. Maintain gutters, downpipes and flashings, and keep ground levels below the damp-proof course.
  2. Use the right mortar. Match the mortar to the bricks. Never use hard cement on soft, older brick.
  3. Do not seal or paint it. Let the wall breathe.
  4. Clean gently. No sandblasting and no strong acids.
  5. Check your walls every year. Look for flaking, loose bricks and failed mortar after winter. Catching it early is the cheapest option. Our article on the signs your house needs repointing shows what to look for.

When Should You Replace the Bricks?

Replace when:

  • The spalling is deeper than about 10 to 15mm, or the brick is crumbling or powdery
  • Several neighbouring bricks are failing
  • The brick is loose or on a chimney stack
  • Repointing and drying out has not stopped the damage

Leave alone and monitor when it is a shallow surface flake on an otherwise hard brick and the cause has been fixed.

Need a Professional?

If you have spalled bricks in Hampshire, Berkshire or Surrey, we can inspect them, tell you straight what is causing the problem and give you a free, honest quote with no pressure. We are brickwork and repointing specialists, not general builders, and we are fully insured.

Message us on WhatsApp for a free quote, or visit rosserbrickwork.co.uk to find out more about our services.

Frequently Asked Questions

Will spalled bricks get worse?

Usually yes, if the cause is not fixed. Each winter the exposed, softer brick absorbs more water and breaks down faster.

Is brick spalling covered by home insurance?

Generally not. Insurers treat it as wear and tear or lack of maintenance. Check your policy wording.

Can I paint over spalled bricks?

We advise against it. Paint traps moisture and often makes spalling worse. Fix the brick and let it breathe.

How long does a spalling repair last?

A proper repair, with the cause fixed and the right mortar, should last decades. A cosmetic patch on a wall that is still wet will not.

Free Tool

Work Out Your Own Repointing Cost

Put in your wall measurements and get a cost range built from the real rates on this page — £60–80 per m² — with scaffolding shown as its own separate line rather than hidden in the total.

Open the Cost Calculator
Advertisement

Need a Professional?

Get a Free Quote from a Brickwork Specialist

If you're in Hampshire, Berkshire or Surrey, Rosser Brickwork & Repointing Services Ltd can handle your repointing, chimney repairs or brick restoration. Fully insured, free quotes, no pressure.