Repointing6 min read

Mortar Mix Ratios for Brickwork: The Complete UK Guide

Get the mortar mix ratio right and your brickwork lasts decades. Here are the correct mixes for repointing, bricklaying and chimneys, and what mix for repointing suits your property.

DR

Daniel Rosser

Published 1 November 2026

Getting the mortar mix ratio right is the single biggest factor in whether brickwork lasts or fails. After years of repointing and building across Hampshire, Berkshire and Surrey, I can tell you the wrong mix is one of the most common reasons I get called back to jobs other people have done. This guide covers the mortar mix ratio for each type of job, what mix for repointing suits which property, and the mistakes to avoid.

Why the Mortar Mix Ratio Matters

Mortar is meant to be the weaker, sacrificial part of a wall. It should be softer than the brick so that moisture and movement are taken up by the joints, not the brick faces. If the mortar is too hard, water gets forced out through the bricks instead, and the faces start to flake off. This is exactly how spalled bricks start on so many UK homes.

The ratio is written as cement (or lime) to sand by volume. A 1:6 mix means one part binder to six parts sand. More binder means a harder, stronger mortar. More sand means a softer, more flexible one.

Mortar Mix Ratios by Job

JobTypical mix (by volume)Notes
Repointing Victorian or older brick1:3 NHL 3.5 lime to sand, or 1:2:9 cement:lime:sandSoft bricks need soft mortar
Repointing 1930s to 1960s brick1:2:9 or 1:1:6 cement:lime:sandDepends on brick hardness
Repointing modern hard brick1:1:6 cement:lime:sandOr 1:5 to 1:6 cement:sand with plasticiser
Building new brickwork (general)1:5 or 1:6 cement:sand with plasticiserStandard for most walls
Garden walls, exposed to frost1:4 to 1:5 cement:sand with plasticiserStronger for freeze-thaw exposure
Chimney stacks1:1:6 cement:lime:sandVery exposed, but avoid going too hard

What Mix for Repointing Old Brickwork?

If your house was built before about 1920, it was almost certainly laid in lime mortar. The bricks are usually softer, and the walls were designed to breathe. For these properties, the answer to what mix for repointing is a lime-based mortar, typically 1:3 lime to sand using a natural hydraulic lime such as NHL 3.5. Using a hard cement mix on old brick is the classic mistake, and it is the reason so many Victorian terraces end up with damaged brick faces.

We cover this in more detail in our guide to lime mortar repointing and in the article on the best mortar mix for repointing old brickwork.

Mortar mix ratio for pointing newer houses

For houses from the 1930s onward, the bricks are generally harder and a gauged mix works well. A mortar mix ratio for pointing of 1:1:6 (cement, lime, sand) is my usual choice. It gives enough strength to last without being so hard it damages the brick. For modern engineering or very hard bricks, a stronger mix is fine, but I rarely go stronger than 1:4 cement to sand for pointing work.

The Rule of Thumb: Mortar Weaker Than Brick

If you are unsure, the rule is simple: the mortar should always be a little weaker than the brick or stone around it. You can do a rough test. Take a small piece of the old mortar and scratch it with a screwdriver. If it crumbles or scratches easily, it is probably lime and you should stay with lime. If it is hard and grey and resists a scratch, it is a cement mortar and a gauged mix will usually be suitable.

Choosing the Right Sand

The sand matters almost as much as the binder. For repointing, the sand should match the original in colour and grain size. A sharp, well-graded building sand is the usual choice, and it is worth getting a sample matched when working on a period property. Too much fine soft sand makes a weak, powdery joint. Too much coarse material makes it hard to finish neatly.

  • Sharp sand: coarser, good for structural bedding mortar
  • Building (soft) sand: finer, better for pointing and a smooth finish
  • Colour matched sand: important for period properties where the joint colour is part of the look

Mixing Mortar Properly

  1. Measure by volume using the same bucket or gauge box every time. Guessing leads to inconsistent colour and strength.
  2. Mix dry ingredients thoroughly before adding water.
  3. Add water gradually. Pointing mortar should be firm and workable, not wet and sloppy.
  4. Use a plasticiser rather than washing-up liquid. Liquid soap introduces too much air and weakens the joint.
  5. Keep each batch the same. Different water levels cause patchy colour once the joints dry.

If you are using lime, remember it needs to be protected from frost and from drying too quickly. Damp down the wall, keep it shaded in summer, and cover it in cold weather.

What Does Repointing Cost?

The mortar itself is a small part of the bill. The labour in raking out the old joints and repointing neatly is where the cost sits. As a guide, rake out and repointing runs at £60 to £80 per m². Chimney repointing is typically £80 to £120 per m² because of the access and exposure. Brick cleaning, if needed, is around £5 to £10 per m².

Scaffolding is always an extra cost and is never included in these figures. For anything above ground floor height, or for a chimney, you should budget £500 to £1,000 or more depending on the height and access. For a full breakdown, see our repointing cost guide.

Common Mortar Mix Mistakes

  • Using pure cement and sand on old brick. Too hard, and it will damage the brick faces.
  • Using a ready-mixed bag without checking what it is. Many are far stronger than an older house needs.
  • Not raking out deep enough. Joints should be cut back to at least twice the joint width, usually 15 to 25mm, before repointing.
  • Overworking the mortar. Brushing too early or too late ruins the finish and weakens the joint surface.
  • Ignoring the weather. Frost, rain or strong sun in the first few days can ruin new pointing.

Frequently Asked Questions

What is the best mortar mix ratio for repointing?

It depends on the age and hardness of the brick. For pre-1920 homes, 1:3 natural hydraulic lime to sand is usual. For newer houses, a 1:1:6 cement, lime and sand mix suits most jobs.

Can I use bricklaying mortar for pointing?

You can, but a pointing mix is usually finer and a little softer. A standard 1:5 or 1:6 bricklaying mix is often stronger than is wise for repointing older brick.

How do I tell if my house has lime or cement mortar?

Scratch a small area with a screwdriver. Lime is softer, lighter and crumbles easily. Cement is hard, grey and tough to scratch. If in doubt, ask a specialist to look before any work starts.

Does the mortar mix affect how long repointing lasts?

Absolutely. The right mix in the right conditions can last 40 years or more. See our guide on how long repointing lasts.

Can I mix mortar myself for a DIY job?

You can for small jobs, but the raking out and finishing take real skill, and a wrong mix is hard to undo. For anything over a small patch, it is worth getting a quote.

Get a Free Quote

If you are not sure what mortar your property needs, or you would like the job done properly the first time, get in touch with Rosser Brickwork & Repointing Services Ltd. We cover Hampshire, Berkshire and Surrey and offer free, no-obligation quotes. Message us on WhatsApp or visit rosserbrickwork.co.uk.

Free Tool

Work Out Your Own Repointing Cost

Put in your wall measurements and get a cost range built from the real rates on this page — £60–80 per m² — with scaffolding shown as its own separate line rather than hidden in the total.

Open the Cost Calculator
Advertisement

Need a Professional?

Get a Free Quote from a Brickwork Specialist

If you're in Hampshire, Berkshire or Surrey, Rosser Brickwork & Repointing Services Ltd can handle your repointing, chimney repairs or brick restoration. Fully insured, free quotes, no pressure.